Dormers · walls · valleys · drip edge

Roof Flashing Repair in Hicksville, NY

Most roof leaks start at a joint, not in the open field of shingles. Dormer walls, valleys and roof-to-wall lines all rely on metal flashing to turn water away. Call Dryline Roof Pros now and we'll replace or re-step failed flashing.

HICKSVILLE, NY · 11801
Roof Flashing RepairNassau County, NY

What is roof flashing repair?

Roof flashing repair replaces or reinstalls the thin metal pieces that seal the joints where a roof meets walls, dormers, chimneys, skylights and other roof slopes. Shingles alone can't seal those transitions. Flashing is layered so that each piece sheds water onto the one below, and it works as long as it's intact and lapped in the right order.

Flashing problems are especially common on Cape Cod houses that have been expanded with dormers, a very familiar sight across Hicksville. Each dormer adds two sloped side walls lined with step flashing, a front edge and sometimes a shallow roof of its own. More joints mean more places to leak, which is why many roof leak experts in Hicksville check the dormers first.

How is roof flashing repaired?

Flashing comes in several types, and each has its own repair:

Step flashing at walls and dormers

Where a sloped roof meets a vertical wall, individual L-shaped pieces are woven in with each course of shingles, one piece per course, each overlapping the one below. When they rust or were installed as one long piece, water gets behind them. We remove the siding's bottom course and the shingles along the wall, installs new step flashing piece by piece, and reinstalls the siding over it.

Counterflashing

On brick or stucco, a second layer of metal laps over the step flashing from above, set into a mortar joint or a cut reglet. It keeps water from running down the wall behind the step flashing.

Valley flashing

Valleys carry more water than any other part of the roof. Open metal valleys or woven and closed-cut shingle valleys over an ice and water membrane are repaired by replacing damaged metal or rebuilding the valley shingles.

Headwall and apron flashing

Where the top of a roof slope meets a wall, such as under the window of a shed dormer or at the front of a porch roof, a continuous apron flashing is bent up behind the siding.

Drip edge

Metal along the eaves and rakes guides water into the gutter and protects the deck edge. Missing or bent drip edge lets water wick back into the fascia and the roof sheathing.

What are the warning signs of failed flashing?

Flashing failures usually show up near walls and joints. Look for these eight signs:

  1. Stains under a dormer. Water marks on the ceiling or knee wall below the dormer's sides.
  2. Wet siding or trim where the roof meets a wall. Peeling paint or rot at the bottom of dormer walls.
  3. Rusty metal. Brown streaks or holes in visible flashing.
  4. Lifted or bent pieces. Metal standing away from the wall or chimney after wind.
  5. Thick caulk everywhere. Layers of old sealant are a sign flashing was patched rather than fixed.
  6. Leaks in wind-driven rain only. Water pushed sideways behind flashing that works in calm rain.
  7. Rotting fascia. Soft wood at the eaves where drip edge is missing.
  8. Valley stains. Ceiling marks lined up below where two roof slopes meet.

What causes roof flashing to fail?

Flashing usually fails from age, corrosion or installation shortcuts:

  • Corrosion. Galvanized steel rusts over decades, especially where leaves and moisture sit.
  • Reused flashing. Old metal bent back and reused during a re-roof instead of replaced.
  • Continuous instead of stepped. One long piece along a wall channels water behind the siding.
  • Face-nailing and caulk. Nails through exposed metal and caulk-only seals fail as the sealant ages.
  • Siding installed tight to the roof. Siding with no gap above the shingles traps water and debris against the flashing.
  • Wind and ice. Storms lift loose pieces, and ice dams force water uphill behind them.

What can you check from the ground?

You can look for flashing trouble safely from the ground and the attic:

  • Scan each dormer. With binoculars, look at where the dormer walls meet the roof for rust, gaps or heavy caulk.
  • Check the valleys. Look for debris piles, damaged shingles or exposed metal.
  • Inspect the knee walls. In Cape Cods, open the small doors to the low attic spaces behind the knee walls and look for water stains below the dormer.
  • Look at the eaves. Check for missing drip edge or rotting fascia boards.
  • Note wind direction. If leaks only happen in storms from one direction, that side's flashing is the prime suspect.

What happens during a flashing repair visit?

Here's how a flashing repair visit usually goes:

  1. Trace the leak. We check the stain, the attic or knee-wall space, and the joint above it.
  2. Inspect the flashing. We look at how it was installed, whether it's stepped, and whether it's rusted or loose.
  3. Quote. A written estimate covering shingles, siding or trim removal and reinstallation.
  4. Open the joint. Shingles along the wall and the bottom course of siding are removed.
  5. Install new flashing. Step flashing piece by piece, plus counterflashing, apron or valley metal as needed, often over ice and water membrane.
  6. Close up and document. Shingles and siding go back, and you get photos of the new flashing before it's covered.

What affects the cost of roof flashing repair?

Flashing jobs vary with how much has to come apart to reach the joint. These factors matter most:

Roof flashing repair cost factors
FactorHow it affects the job
Length of the jointA short wall section is quicker than both sides of a long shed dormer.
Siding typeVinyl siding comes off easily. Cedar shakes, stucco or brick need more care.
Flashing materialAluminum, galvanized steel and copper vary in cost and workability.
Hidden rotWet sheathing or wall framing found behind old flashing must be replaced.
Roof pitchSteep dormer roofs need extra safety setup.
Combined workChimney or skylight flashing done at the same time can share setup costs.

We photograph the new flashing before shingles and siding go back over it, since you won't be able to see it afterward.

When is a flashing leak an emergency?

A flashing leak is urgent if water is running down a wall inside, soaking a ceiling, or a big piece of metal has blown loose. Water behind siding can quietly rot sheathing and framing. If it's coming in fast, start with emergency roof leak repair.

A small stain that appears only in wind-driven storms can usually wait for a scheduled repair. Book it before winter, because ice dams push water behind weak flashing.

Roof flashing repair FAQs

Can flashing just be resealed with caulk?

Caulk can buy time, but it isn't a repair. Flashing works by overlapping in the right order. Once it's rusted, reused or installed wrong, it needs to be replaced.

Why does my dormer leak?

Dormer leaks most often come from failed step flashing along the side walls, missing apron flashing at the front, or siding installed too close to the roof. We can tell which by opening the joint.

Does the siding have to come off to fix flashing?

Usually the bottom course or two does, so the new step flashing can be tucked behind it. Vinyl siding comes off and goes back easily. Other materials take more care.

Should flashing be replaced during a re-roof?

Yes, in most cases. Reusing old flashing saves a little upfront but often leads to leaks later. New step flashing and drip edge are standard on a quality re-roof.

What is drip edge?

It's metal trim along the roof's edges that guides water into the gutter and keeps it from wicking back into the wood. Older roofs sometimes don't have it.

Is copper flashing worth it?

Copper lasts a very long time and looks good, but it costs more. Aluminum and galvanized steel are common choices on homes. The installation matters more than the metal.

Roof flashing repair in Hicksville neighborhoods

Flashing work comes up all over Hicksville. Gable roofs in Hicksville Gables have long valleys and rake edges that depend on good flashing. Single-family streets in Field Estates often have dormer additions with step flashing that's aging out. Pick your neighborhood below.

Call now

Seal the joints where roofs really leak.

Call Dryline Roof Pros and we'll replace dormer, wall, valley and edge flashing the right way.

516-839-3333
Tap to call now
Roof leaking in Hicksville?Fast local roof help
Call 516-839-3333